Some explanation from Edwin :
The exterior desing of the car is inspired by the form of fabric blown in the wind. The form also carries traces of the historical Auto Union Type C Streamline race.

There are no conventional doors on the car, but instead, inspired by the jet fighters, there are three glass canopies. The main canopy opens forward together with the steering wheel and the dashboard; the two passengers’ canopies open backwards; and a side panel on the bodywork opens downwards to act as a step, making the event of getting in and out of the cockpit very special and easy.

The interior is simply one continuous sheet, starting from the dashboard, then being folded and bended to create floor carpet and seat.

The interior of the car is as simple and futuristic as the exterior. Single sheet transparent LCD dashboard displays all the essential data such as speed and mileage. The screen in the center of the steering wheel displays digital map. The information can also be projected on the canopy by a head up display. The
whole driving experience would be like flying a fighter jet. There is a small but handy luggage space behind the driver seat for handbags and suitcases. It is also an arm rest for the passengers.

Four wheels are housed inside the car’s four “legs”. Each wheel contains an Audi In-wheel Electric Drive Unit, making the car an evolution in Audi’s trademark “Quattro” all time four-wheel-drive system. The long range Supercharge-ion battery which powers the in-wheel motors are separated into two packs located in front of as well as behind the cockpit, creating a perfect 50:50 weight distribution of the car for excellent handling.

Specifications:
Length: 4480 mm
Width: 1900 mm
Height: 1060 mm
Wheel base; 3048 mm
Weight: 800 kg
En Engine: 4 Audi In-wheel Electric Drive Units
Power: 544 hp (4 X 100 kW)
Torque: 4500 Nm (3319.03 lb-ft)
0-100km: 2.9 s
Top Speed: 360 km/h

Designer : Edwin Conan

The Expandable Recycling bin features a low starting and increases its height gradually with the wastages, allowing effective space management and low drop for brittle electronics. The facility manager of an apartment or office can have a visual feedback through the expansion and a maximum size bin denotes it needed to be emptied. It features a RFID locking system that ensures only valid residents with a RFID tag can open and use the bin. Besides, there will be a designated person with a special access tag to unlock the wheels. Biopregs, an eco-friendly bio-composite is the main material that has been used to create the two major parts of the bin. Cautious emptying in the pickup-vehicle has been ensured by placing a reusable bag in the bin which is lifted out with a crane. The bag is prepared of heavy duty fabric with durable chemical proof coating.

Designer : SpringTime

Designer : Mingoo Kim, Yunjin Chang, and Sueun Park

This proposal is focused around providing an alternative view of what the future of the Taxi might be. The vehicle is designed around the user and this is reflected in the safety of ingress/egress, the passenger/driver compartment split and features for ease of use by passengers. Features include, split for driver safety when used as night rider, GPS and mapping system for driver and passenger, passenger entertainment/info hub, Smart card system, disability access and focus on curb side access only. Technological features include the hydrogen fuel cell, battery generators, solar panel system and recharging hubs.

The overall aesthetic of the vehicle is influenced by the Australian environment; space, relaxed ambience, unique identity, comfort, security, and a ‘can do’ attitude. These unique characteristics immediately identify the vehicle as special purpose and also set it apart from other vehicles on the road. The curb-side DLO captures the essence of the Taxi in that it is inviting passengers inside for an experience.

The footprint is emphasized by the wheels being in the outermost corners of the vehicle which allows for greater volume and also a very level and balanced stance. The roof features an acrylic opening area to allow for a greater sense of space while also allowing a great vantage point for passengers. The solar panel is also cleverly housed on the roof to harness the most energy from beating Australian sun.

Curb side access only for passenger ingress / egress safety. All doors use a slider system for minimizing the overall footprint of the vehicle whilst it is in operation. Access for wheel-chair bound passengers is catered for by providing a platform that extends to the curbside to allow access. All rear compartment seats tuck away to open-up maximum floor room for wheelchair access. Rear trunk also operates on a slider system.

The rear compartment is split-up to allow for better communication for the rear occupants. Rear seats fold away to allow access and floor clearance for wheelchair access. Heads-up display on split window for accessing features such as map, places of interest, fares and also for advertising. Driver to passenger split is driven by – safety and privacy. The split ensures security of the drivers whilst also providing a more private booth-type environment for passengers. Doors split open at the centre to allow for maximum operating opening distance.

Polycarbonate is used throughout the vehicle due to its impact resistance, relative lightweight, optical qualities and high temp resistance. The chassis comprises of aluminum to minimize weight.

Curb-side access only for passenger safety, bright orange livery for visual impact, safety-cell for passengers and driver all contribute to overall safety. Optimized seating configuration allows greater interaction, comfort and ease of use – especially the fold away seats for wheelchair access.

Hydrogen fuel cell technology coupled with electric generators / batteries propel the vehicle. The solar panel is used to harness extra energy as well as the recharging hubs when the vehicle is used to pick up passengers.

Designer : Damian Lucaciu

This electrically powered futuristic concept vehicle houses two passengers and includes four motors, one for each wheel, which will let the wheels to swivel on its center by inverse rotation. These motors are located inside every wheel and the wheel rims are designed to act like a propeller to keep the system cool. Besides, another motor exists in the center pivot that provides the required power to change the appearance of the car, like opening the trunk door or modifying the seat arrangements.

The dimension of this car is 1.75 x 1.75 meters approx. when it is in compact mode. By using a geometry stimulated from the ‘bioarchitecture’ of a moving cat, this hybrid formed car changes its attitude with his postures.

Designer : David Vega

Rotating arms have been used in order to keep the seats level for both vertical and horizontal drive. When the vehicle is in balcony mode, the seats are positioned on a rolling base which allows them to become lounge chair for lying down and relax. The exterior design of this car never seems like a car that is mounted vertically with a building but still it looks like a vehicle on the road. The wheels are hidden towards inside and doors are designed to rotate closely around the car, instead of the usual pulling out or sliding up doors, allowing the entrance to freely open in narrow area like a garage.

Designer : Roman Mistiuk

Adam explanations about A.R.C :

The ‘A.R.C’ (Amphibious Rescue Craft) is a rugged all terrain vehicle that can be used to deliver vital aid and supplies anywhere required including flooded areas which are inaccessible to most other vehicles. Variable height ground clearance combined with large wheels and all terrain tyres provide excellent off road capabilities, whilst a boat hull and retractable wheels enable the A.R.C to plane at high speeds across water with minimal friction and uncompromised performance.

The high output diesel engine powers the wheels when on land and the water jet propulsion system when waterborne which can deliver up to one tonne of thrust. Once landed at its destination, the A.R.C uses an on-board crane (known as a ‘Multilift’ system) to rapidly deploy a supply unit containing anything from medicine or food to a water purification system. The water filtration units can be deployed at the site of a mass flood and used to purify contaminated flood water, returning it to life-saving drinking water which is otherwise scarce in flooded third world environments.

Supply units can also be opened to form mobile shelters for distribution of supplies or temporary living quarters/command centres etc. An unfoldable canopy marked with an ID symbol and number (e.g. Red Cross, Supply Unit number etc.) provides shelter from the rain and can be easily identified by passing rescue helicopters. The name A.R.C not only stands for Amphibious Rescue Craft but also identifies with Noah’s Arc which was believed to have been used as rescue / refuge craft during a mass flood.

Designer : Adam Schacter

Designer : Dave Strydom

What Petr say about this Robotic Taxi :

Instruction to use robotaxi
- You call taxi by mobile phone
- Robotaxi operator will evaluate the closest taxi
- Robotaxi will arrive in very short time and open the door for you
- Put your baggage and go inside the taxi
- You need to set your destination (by your voice or by touch panel)
- While in the road, you can watch video on double-sided cabin window or surfing on internet
- Payment will be done automatically (by wireless reading from you credit card)

Designer : Petr Kubik

[Press Release]
Honda FC Sport Design Study Suggests Hydrogen Sports Car Future

LOS ANGELES, Nov. 19, 2008 – Honda today revealed the Honda FC Sport design study model, a hydrogen-powered, three-seat sports car concept, at the 2008 Los Angeles Auto Show.

The FC Sport emphasizes the design flexibility and potential of Honda’s V Flow fuel cell technology – already deployed in the Honda FCX Clarity sedan – and reconfigures it into a lightweight sports car design with an ultra-low center of gravity, powerful electric motor performance and zero-emissions. The design study concept is inspired by supercar levels of performance through low weight and a high-performance, electrically driven fuel cell powertrain.

“The Honda FC Sport explores how to satisfy automotive performance enthusiasts in a world beyond petroleum,” said Dan Bonawitz, vice president of American Honda Motor Co., Inc. “People who love sports cars will still have a reason to love in a hydrogen-powered future.”

The high-output Honda fuel cell powertrain and a sleek, aerodynamic body contribute to the vehicle’s performance potential. A modular approach to fuel cell component packaging and the electric drivetrain contribute to the FC Sport’s low center of gravity with the majority of vehicle mass distributed between the axles, creating the balanced weight distribution sought after in sports cars.

The ideal placement of the Honda V-Flow fuel cell stack and related components demonstrates the benefits of a platform-specific, hydrogen-powered fuel cell powertrain. The FC Sport is configured to accommodate a custom-formed high-power fuel cell stack, located between the rear seats, and a battery pack placed low in the middle of the vehicle. The electric motor resides just forward of the rear axle. Two fuel storage tanks, visible from above, are located above the rear axle.

The optimal placement of fuel cell components for performance also allows for a relatively large passenger cabin by conventional supercar standards with enough space for three seating positions. The interior layout focuses primarily on the driver with a racecar-like center driving position. The enclosed canopy opens upward from the rear to allow for entry and exit. Two rear passenger seats flank the driver’s left and right side.

The sleek, low-profile body is designed to convey a high-technology appearance with sculpting that combines angular shapes in the front of the vehicle that taper into geometric, hex forms in the rear. The rear hex forms house cooling radiators for the fuel cell. Formula 1-style barge boards behind the front wheels enhance high speed aerodynamics and convey the vehicle’s racing pedigree. The hydrogen storage tanks, visible from the rear deck, showcase the FC Sports fuel cell technology in much the same way that a “naked bike” motorcycle showcases its engineering technology.

The glacier white body color conveys the FC Sport’s clean environmental aspirations while the dark wheels and deeply tinted glass provide a symbolic contrast befitting of the vehicle’s unique combination of clean power and high performance. Green construction techniques further contribute to a reduced carbon footprint. An organic, bio-structure theme is carried through to the body construction where exterior panels are intended to use plant-derived bio-plastics.

The Advanced Design Studio of Honda R&D Americas, in Pasadena, California, developed the FC Sport design study with the primary objective of using existing fuel cell technology as the basis for an ultimate Honda sports car. Designer Jason Wilbur led the design efforts.

Honda R&D Americas, Inc. began its operations in California in 1975 with local market research activities and has steadily grown its capabilities over the past 33 years to include all aspects of new vehicle design and development. Recent development efforts include trend-setting products such as the Honda Pilot, Ridgeline, Element, Civic Coupe and Civic Si.

In 2008, the company opened two new design centers in Southern California: the Acura Design Studio (Torrance), for the research and design of new Acura products; and the Advanced Design Studio (Pasadena), for the exploration and development of advanced design themes for both Honda and Acura.

The company operates 11 major R&D facilities in North America, including a full vehicle development center in Raymond, Ohio, and three design studios in Southern California. Honda R&D designers, engineers and support personnel are engaged in the development of Honda and Acura automobiles, powersports products, and power equipment for North America and global markets. The company’s main centers of operation include the Los Angeles Center (Torrance, California), responsible for market research, concept development and styling design; the Ohio Center (Raymond, Ohio), responsible for complete product development, testing, and support of North American supplier and manufacturing operations; and a dynamic test facility in Cantil, California.