Designer : Liviu Tudoran

Explanation from Petr:
The exhibit is an active relaxation and rehabilitation bath with special features that permit the changeability of water volume (0-410 L) and provides a pleasant form of relaxation due to its continual and smooth changes to the ergonomical shape of the structure. The bottom contour of the bath adjusts in order to conform to the required position and height of the user. The various geometrical changes to the shape enables the bath to be “shortened” for example, creating a backing for the legs in order to maximize on comfort.

For the purpose of saving on water consumption, one can simply change the depth of the bath so it becomes shallow or select a shape that is most suitable for the user. The changes to the shape of the bath floor can be modified & readjusted anytime. Another wonderful trait of the bath is that it is equally convenient for bathing children, because one can adjust a safe depth of bath, reducing risk of drowning as well as being equipped with soft finish of the base. In addition to creating minimal dimensions, the bath itself can be used as a baby changing table. Getting in and out of the bath tub is simple and effortless. There’s no need to climb over edges of the bath. This way, it is beneficial for people with physical disability or those completely immobile.

Uniquely, in this bath we can experience an unmissable feeling of soft, rippling of the bath floor during bathing or when having a massage. This is a new form of relaxation which we can daringly refer to as “kinetic therapy”. The type of technology used forms system of 10 pneumatic pistons (compressed air powering pistons) and includes inclinable segments covered with soft upholstery. This lining creates a pleasant feeling without causing pressure on the body even in the case when the bath is low filled or during the filling or draining of the bath tub. The movable segments are covered by special, highly elastic, hygienic and strong foil (used in the concept of BMW Gina. The geometric shape of the head rest can be partially changed and is also made from movable structures, covered in flexible foil. The type of material`s used are synthetic rock (e.g. ceramics, plastic shroud), glass, elastic foil.

Other systems used are classic hydro/air massaging jets capable of being rotated and powered by electric motor. The connection to mains water supply, water outlet, air and hydro massage jet is through flexible hosing. The bottom of the tub is sealed and the whole base can be raised or lowered over a flat surface of the inner side-panels of the bath. That is how water tightness is ensured.

Everything is controlled electronically with a remote control. As a result, it is possible to select filling/draining of the bath, change water temperature, adjust hydro/air massage settings (duration, intensity, cycle program) and change the shape of the bath floor whit comfortably resting in the bath tub. This is done with the help of sensor button on the display of a remote control. The geometry of the bath can be altered simply by means of accessing touch display screen on the remote control. Naturally, the program remembers previous settings and if the conditions allow, the bath immediately fulfills the command of the user. Simultaneously however, whilst making the change, the height of the water surface, its volume and temperature as well as the total water consumption is electronically monitored.

The filling of the bath is possible through water inlets positioned right beneath the head rest, whilst draining is carried out through the segment located in the middle of the bath tub. If we were to come back to the principle of shaping the bath floor, an alternative method exists, which replaces pneumatic pistons and electrically tilted segments with air pouch system (ballonet). In addition, the foil covering the surface of various segments can also be replaced with a variety of other materials available on the market, that have similar properties.

Designer : Petr Kubik

Designer : Tom Mudra and Hans-Tobias Schicktanz

Victor says about Mytho :

The MYtho, is a concept car designed to be simple, but at the same time sophisticated. With inspiration from vintage cars, like the woodies, i was able to find a sustainable design solution for the side panels, which are made of compressed wood also the whole body is made of aluminum, in order to be recyclable.

The “tech” factor is in it’s OLED displays, build-in solar cells, and HUD display’s for the driver.

The form of the car is very simple, like the hot rods from the 30’s. The open wheel design, the huge front grill, and the low profile of the car, are just some indicators of this.

Designer : Victor Uribe Chacon

Designer : Janak Mistry

Text from Rafael :

Problem
To develop a plant system, for a circular house, based on the silver generation theme, that would bring a comfortable time for the couple together during cooking, with a healthy life concept behind.

Concept
A product that can help them at the kitchen, integrate the environment (kitchen at the middle of the circular house), providing a healthy life style with organic foods, making the cooking moment easy, simple and fun. A hydroponic indoor system witch the aim is to rescue the pleasure of growing and prepare our own food without working hard or spend so much time, exploring the shape of the DNA molecule, the grow of a new life. The product is made simple, two vertical metal tubes where the germinated seeds of the plants are placed into some small holes around the tubes. A net hold it till it starts to grow.There also a light system, with a mobile light focus that can be programed along the path where it moves, providing the right time of light for certain plant. The hydroponic process is based on the NFT hydroponic system, a active process where a solution with nutrients its bombed from a deposit to the culture channel. Part of the root of the plant its getting a constant water flux, while the other part is in direct contact with the humid air.

Justification
Sören and his wife have not so much time together, so when they are able to have a meal at home, his wife likes to prepare it herself, with calm and love. This rare moments that the couple have together are the main point that this project explores.

Materials and Fabrication Process
3 Metal tubes; 2 running from top to bottom of the kitchen, 1 that works like a path for the light. The tubes have a shape conformation, till it reaches the shape of the DNA. They have small connexions outside the house that makes the water flux works in a cycle, with a bomb to provide this. A small programed engine makes the movement of the light along the third tube, right on the middle of the structure.

This project was based on a briefing of the International Design Award (IDA2009).

Designer : Rafael Fernando and Débora Nogueira

The minimalist interior features control steering pod, a mimicking game like control where brake and gas paddles embedded close to the steering wheel, offering next generation driving environment. The wheels are fully immersed with rubberized tire with independent spoke arrangement that allows the wheels to absorb the road bumps without having used the suspensions. Moreover, the out of the body wheel base has added few extra with the innovative look that the car already has with its clear body shell and green house like design.

The technology aspect of Pholeum includes a composition of memory plastic body work, allowing the material to be deformed back to its original shape under application of heat from scratches and dents. These plastic can be recycled further and remolded again into the same component if the damage is irreparable. The chassis is made of durable aluminum alloy, making the vehicle strong and lightweight. Comprehensive safety for the driver has been ensured with three external airbags, designed to deploy by sensing a fast automobile within a few meters of its radius through motion sensors. Each wheel contains quad electric motors empowered with efficient next generation hydrogen fuel cell technology.

Designer : Alexei Mikhailov

Designer : Purisme

Passengers will have great view over the big window located at the front of the boat, stretching to the roof from the floor. The on top LED light integrated lantern will make it easy to dock the boat at night. Upper deck is surrounded by glass to provide easy controlling the boat without disturbing pillars. This gives a much better view as well while giving a more open feeling. Outside the deck, there are security rails as a part of the hull structure that elongates backwards with the wings. A thin glass is designed to rise from the hull at the front to attach the wings at the back, making the boat simple and clean.

The interior of the lower deck is separated in two different parts, one is a private section and another one is an open lounge area, allowing the passengers to rest for a while or participate in social activities as they want. The master bedroom is located in the center which is the best place to be maximum comfortable because of the stability during any directional movements of the yacht. This concept won the award from azimut, and was shown at Piazza San Carlo in Turin ITALY in a big Azimut Event.

Specs:
LENGHT OVERALL(incl.pulpit) 22.05m
HYLL LENGHT(incl.platform) 21.73m
BEAM AT MAIN SECTION 5.12m
DRAFTS(incl.props. at full load) 1.79m
DISPLACEMENT(at full load) 33.2t
ENGINES 2×1410mHP (1036kw) MAN 12V CRM
MAXIMUM SPEED(at half load) 39 knots
CRUISING SPEED( at half load) 32 knots
FUEL CAPACITY 3.300L
WATER CAPACITY 980L
CABINS 3+1 CREW
BERTHS 6+1 CREW
BUILDING MATERIAL CARBON FIBER/VTR/GPR
KEEL V-shape with angle of deadrise 15,4 degrees aft.

Designer : Anders Gloslie

Interview with Nico :

What was the inspiration for your concept?
The inspiration was the experimental approach to molecular cooking. Even after several decades of molecular cuisine, it still seems to be an exclusive game for specialists. So it became my main goal to bring some of the fantastic possibilities and ideas of molecular cooking to all ambitious cooks with an easy to use, affordable appliance.

How does your concept fit into this year’s competition theme “Designs for the next 90 years”?
I think the idea of molecular cooking is forward-looking, but the procedures and methods of preparing molecular dishes are still conventional. I would like to change this with my concept. At first, the idea of printing food seems to be something straight out of a science-fiction movie, but on second thought it is not unrealistic at all. I even think that Moléculaire could be the future kitchen tool that opens up possibilities for food-makers interested in molecular cooking.

What are the main consumer benefits of your concept?
Moléculaire is a futuristic kitchen appliance that offers several new possibilities to professional chefs as well as home users. It’s based on a layer-by-layer printing technique that arranges small particles from a set of ingredients. Within minutes, it prints out three-dimensional desserts, complex structures, shapes for molecular dishes, and patterns for decorating a meal. In addition, it’s easy to use. You simply insert a blister pack into the reservoir, place Moléculaire on top of a plate, and press the start button. Users can also create their own recipes with special software and their own ingredients. Ambitious users can download recipes and share them with other users in an online community.

Describe the consumer research behind your concept.
I conducted interviews with chefs and did a lot of research on the Internet. These approaches helped me to understand users’ interests, concerns, wishes, needs and desires. The outcome shaped my initial ideas and helped them grow. The most difficult thing about designing for the future is predicting the possible social and technological developments (their direction and speed). Therefore, it was very useful to read reports like sociological studies about cooking and future scenarios about the development of new technologies.

What kind of materials would you use to build your concept?
For my concept, I would use polycarbonate as the main material. I plan on applying this material in three different variations, each providing the right characteristics for the different parts of my design. Transparent polycarbonate can be used for the window, black tinted for the lid/display, and white for the body. The robotic printer arm and head could be made from aluminum. A blue (O)LED backlight accentuates the processes inside the printer.

Who is your favorite designer?
I don‘t have a favorite designer.

What are your career goals?
After I graduate in 2010, I want to gain more professional experience in a product-design company. In the long term, I want to further develop my conceptual and strategic skills and step into product-related design management.

Designer : Nico Kläber